YLY-2088 400W Adjustable 2 Way Crossover Filters 1 Unit Audio Speaker Frequency Divider Full Range Treble Bass

Crossover we all know, is installed inside the speaker, to achieve sub-tone, change the effect. Ancient crossover is rigid, the user installed if not suitable, will not be able to change, sometimes encountered treble too strong bass surface poor, or bass is too thick overall performance is not clear, etc., for the beginner is very difficult to solve; if the replacement of the crossover is not necessarily appropriate and high cost.

Debug crossover is a multi-purpose, to achieve a comprehensive debugging, no welding, very convenient to use and the effect of the listener can according to their own preferences; to achieve debugging self-control. Debugging crossover frequency is active, the need for users to know how to use, similar to a knife, knife and then good, if people do not know how to use or do not go to use, but also can not play the advantages. Please watch carefully how to debug. Debugging crossover use a wide range of available treble + bass dichroic speakers, but also available 2.1 small satellite box and car full-range coaxial speakers, but also can be used alone only all the way to the treble or alone only low; sound all the way. Speaker 2-16 ohm impedance can be used, power as long as the speaker in the 400W below are used without problems.

Product Parameter

Size: 7cm long, 5cm wide, 2.5cm thick.

Frequency: not fixed position, determined by the debugging.

Power: speakers below 400W are available.

Impedance: 2-16 ohms.

Material: inductor using oxygen-free copper winding, pure copper thick line 08 or so wire diameter of the shop has been verified. Large capacity capacitors, reasonable design, beautiful appearance and sound quality to achieve full self-control.

Product features

Crossover with terminals, wiring is very convenient, if coupled with the speaker plug spring, you can achieve a full range of welding. Crossover board marked input is connected to the rear box or amplifier, high and low on the connection to the tweeter and woofer. If it is a single full-range, will be high and low + pole line and can be together; if it is a single bass or a single tweeter, the other way all the way empty not connected.

High and low dichroic wiring

INPUT/Input: connect to the amplifier or rear box; TREBLE/Treble: connect to the tweeter; BASS/Bass: connect to the woofer.

Terminal block screwing line operation with a small - the word screwdriver, anti-clockwise direction to loosen the pressure piece down, the wire skinning inserted, clockwise tighten can be.

Full-range coaxial wiring method

Connect the speakers to the BASS/bass position, and then find a - section of small wire, from the positive electrode of the bass to the positive electrode of the treble.

This section can be used individually with the treble or bass, do not use all the way to empty on the warm tips: manpower screwing force will be stronger than the fixed feet of the terminal block to avoid screwing deformation, screwing with your fingers to pinch the terminal block to screw. In case the screwing is too loose resulting in the pressure plate screwed up, the crossover inverted over, the pressure plate screwed up, and then return to the wiring.

2088 original wiring high and low two speakers: according to the above diagram method of wiring. Full-range single speaker: connected to the bass position, and then from the treble ‘+’ to connect an additional section of wire to the bass ‘+’.

The original version is usually inserted ‘A’ and ‘C’ cap, do not insert ‘B’ and ‘D’ cap, is the most commonly used settings, accounting for more than 70% of users can be satisfied! The most common setting, more than 70% of users can be satisfied, after listening to the effect, if you want the treble to become a little bigger on the insertion of ‘D’ cap, if you want the treble to become a little smaller, pull out the ‘C’ - cap for the insertion of the ‘D’ cap.

Insert ‘A’ and ‘C’ is the standard high and low dichroic.

Inserting ‘A’ and ‘D’ is a kind of rich low frequency.

Inserting ‘A’ and ‘C+D’ is a kind of rich high frequency.

Inserting ‘A+B+C+D’ is a way to enrich the middle frequency.

The ‘A’ position is usually plugged in, when using a small-sized woofer or speaker subwoofer is too thick speakers can not stand the distortion, you can pull up the ‘A’, limiting the subwoofer to try the effect.

Try more different music songs, you like the effect of which settings on which debugging crossover is the biggest advantage is that you can adjust a variety of different effects, so that users to choose their favourite one.