Electric Shaver 8806 Three-in-One Shaving Kit Men's Electric Shaver Washable USB Rechargeable

Model: LK-8806 Simple Package Weight: 190G (Including Box)

Power: 4W Voltage: 220V USB Charging

2. the Blade Is Automatically Ground Blade Net. When the Shaver Is Working, the Blade and the Hard Alloy Mesh Cover Are Constantly Ground, Which Can Keep the Blade Sharp Frequently.

3. This Model Is Used for the First Time. Please Charge It for 8 Hours before Using It. If You Don't Use It for Half a Month, You Must Charge It for 8 Hours before Using It. Make Sure That the Rechargeable Battery Does Not Lose Power, keep the Battery Capacity So That You Can Prolong the Life of the Shaver.

4. the Battery (1.2V) of This Shaver Is Recharged 500 Times, and the Capacity Remains Unchanged.

5. This Shaver Is a High-Speed Silver Palladium Motor with Long Service Life, Low Noise, High Power and Light Vibration.

Razor Tips

1. the Cutter Head Should Be Thoroughly Cleaned Every Four Weeks. after Removing the Net Film Frame, Spray Special Detergent 5cm Away from the Net Frame, and Then Use a Small Brush to Remove the Residue and Dirt in the Cutter Head Later.

2. Use a Small Brush to Clean the Cutter Head, and Use a Small Brush to Clean the Net Film to Avoid Damage.

3. after Each Shaving, Remove the Screen Frame, Tap It on the Plane a Few Times and Then Install It Again.

4. Every Time You Use the Back Cover, the Protection Cover of the Internet Film Cutter Head Can Prevent the Screen Film from Being Damaged.

5. in Order to Ensure the High Level Effect of Electric Shaver, It Is Especially Recommended That You Replace the Cutter Head and Knife Net Every Two Years.

6. in Order to Maintain the Service Life of the Battery in the Machine, Completely Drain the Razor during Normal Use Every Half a Year, and Then Recharge It Again.

7. Because the Face Will Expand Slightly after Washing Face, It Is Best to Shave before Washing Face. It Is an Ideal Time to Shave before Washing Face after Getting up in the Morning.

8. When Using the Film Shaver, Keep the Shaver Perpendicular to the Face and Hold the Electric Shaver at a Right Angle of 90 Degrees.

9. Because the Beard Grows Downward, the Beard Can Stand Upright Only by Reverse Scraping, Which Is Convenient for Scraping. Therefore, the Beard Should Be Scraped Backward from Bottom to Top When Shaving.

10. When Shaving, Tighten the Skin by Hand. Do Not Push the Cutter Head Hard. You Can Shave the Residue Only by Gently Sliding over the Hu District.

[Charging Method]

1. Be Sure to Use Ac 220V/50Hz to Charge

2. Turn off the Switch, Push out the Charging Pin and Insert It into the Power Socket.

3. When the Switch Is Not Closed, It Cannot Be Charged.

4. When Charging, the Charging Indicator Light Is on.

5. the Standard Charging Time Is 2 Hours.

[Precautions]:

Do Not Charge in Areas Where the Rated Voltage Exceeds 240V, Otherwise Failure Will Occur.

Do Not Charge Continuously for More than 24 Hours, Or Charge When the Temperature Is Lower than 0℃ Or Higher than 40℃, Otherwise the Battery Life Will Be Shortened.

Do Not Use Water to Washer Body, and Do Not Bring It into the Bathroom for Use, Otherwise It Will Break down.

When the Body Is Dirty, You Can Use a Soft Cloth to Dip Neutral Lotion to Wipe It. Do Not Use Alcohol Or Gasoline to Wipe It.

When Abnormal Conditions (Such as Smell, Temperature, and Sound) Occur during Charging Or Using the Product, the Power Supply Should Be Cut off Immediately and the Use Should Be Stopped.

Proper Use and Maintenance of Electric Shaver Can Not Only Achieve Satisfactory Shaving Effect, but Also Prolong the Service Life of Electric Shaver. Attention Should Be Paid to the following Aspects When Using It.

1. When Installing the Power Supply, Pay Attention to the Polarity of the Dry Battery Or Charger to Prevent the Motor from Turning Upside down, Thus Damaging the Fixed Blade and Moving Blade.

2. at Pogonotomy, the Fixed Blade Should Be Pressed Tightly against the Face Slowly, and the Beard Should Move against the Growth Direction, So That the Beard Can Enter the Mesh Smoothly. If You Move along the Beard, It Will Overwhelm the Beard, Which Is Not Conducive to the Beard Entering the Mesh.

3. Electric Shaver Is Not Suitable for Shaving Long Beard, So It Is Better to Shave Every 4 Days Or So. If the Beard Is Long, You Should Cut It Short with Trim Or Small Scissors First, and Then Shave It off with an Electric Shaver. If There Is No Trim Or Small Scissors, You Should Use Multiple Shaving Methods to Touch the Skin Vertically with the Fixed Blade (Mesh Cover) and Beard, and Shave the Beard Shorter, then Proceed According to the Method of 2.

4. When Using the Electric Shaver with Trim, the Blade of Trim Should Be Moved at a Vertical Angle with the Face to Clean the Beard.

5. Once the Rolling Stop Occurs at Pogonotomy, Turn off the Power Supply and Restart It. after the Motor Rotates Normally, Continue to Pogonotomy.

6. the Fixed Blade of the Electric Shaver Is Very Thin and Cannot Be Forced to Deform Or Damage It.

7. for Dry Cell Battery Electric Shaver, Take out the Battery after Using It Or Lay up for a Long Time to Avoid Unnecessary Corrosion and Damage Caused by Moisture and Liquid Leakage. AC Type Electric Shaver Should Cut off the Power Supply and Pull out the Plug after Use to Ensure Safety. Rechargeable Electric Shaver Cannot Discharge Too Much Power. If the Battery Is Insufficient, It Should Be Charged before Use. If It Is Lay up for a Long Time, It Should Also Be Charged Regularly (about Three One Months).

8. Add a Small Amount of Lubricating Oil to the Bearing Part Regularly to Reduce Wear. Non-Wet Electric Shaver, Do Not Wash with Volatile Chemicals Such as Water Or Alcohol. If the Blade of Non-Stainless Steel Material Is Not Used for a Long Time, a Thin Layer of Oil Should Be Applied to the Blade to Prevent Rust from Damaging the Blade.