Full Auto OBD2 OBDII code reader, Cartner jdiag T200, OBD2 Scanner, car diagnostic tool, compatible with PK ELM327

📌Warm Tip: jdiag T200 only supports engine system and cannot support ABS SRS airbag system. If you need equipment supporting this system, please contact seller to provide new products

📌And the jdiag T200 equipment is connected directly to the Car OBD2 diagnostic socket to get power for diagnosis, just plug ready to use, no need to recharge

📣Product Introduction

T200 scanner is suitable for all OBD LL compliant vehicles (matches up to 97% of car models), and supports fault code search, reading vehicle information, viewing real-time data flow, reading fault code, cleaning code damage, L/M readiness test, Etc., makes T200 the best choice for automotive repair tools.

📣Protocol supported

1. ISO9141-2 (5 baud init, 10.4 Kbaud)

2. SAE J1850 PWM (41.6 Kbaud)

3. SAE J1850 VPw (10.4 Kbaud)

4. ISO14230-4 KWP (5 baud init, 10.4 Kbaud)

5. ISO14230-4 kWp (init fast, 10.4 kbaud)

6. ISO15765-4 can (ID 11bit, 500 kbaud)

7. ISO15765-4 can (29bit ID, 500 kbaud)

8. ISO15765-4 can (ID 11bit, 250 kbaud)

9. ISO15765-4 can (29bit ID, 250 kbaud)

📣Product Specification:

📌Display screen: 2.4 inch TFT color screen (320*240)

📌Operating temperature: -20 ~ 60℃ (-4 ~ 140 °f)

📌Storage Temperature: -20 ~ 70℃ (-4 ~ 158 °f)

📌External power: 8V-30V DC

📣This is specifically designed for engines called "Car heart". It is necessary to observe the engine status to ensure efficient engine operation to ensure the safety of your trip. Besides, it can also be used before you send the car to the discharge test. Great for daily repair work. The table below describes the purpose of each mode of operation:

1. Chimney Code

2. code delete

Data 3.Live

4. Freeze Frame

5. Kesediaan I / M

6. o2 sensor test

7. test monitor on board

8. EVAP Sistem

9. vehicle information

10. Ujian Compones

Carian DTC

📣Operation instructions

📌Connecting scanner

1. turn off the ignition switch

2. find vehicle 16-pin data link connector

3. plug the obdll cable into the vehicle DLC

4. turn on the ignition and engine

5. when finished, the device automatically enters the diagnostic interface

📌Chimney DTC

Select [OBD] and then [read DTC], press the button [OK] Key to proceed, if there is a fault code, the screen will display the code (Figure 2), if you find more than one DTC error code, please use the left/right key to twine the page to check all code.

📌Clear DTC

Before cleaning the fault code, please follow the fault code instructions to carry out vehicle maintenance, vehicle maintenance can be completed to clean the fault code operation.

Select [clear DTC] and press the button [OK] Key to proceed, the display will show as follows:

Note: cleaning the fault code does not mean the fault code in the ECU has been completely deleted; the fault code will continue to appear as long as the vehicle has damage.

📌Status I / M

The [I / M status] function is used to check the operation of the emission system on vehicles that comply with OBD Ⅱ, and is an excellent feature for checking vehicle compliance with the national emission test. It is an excellent feature to check vehicle compliance with the national emission test. The status of L/M can be selected from the existing obvious or standby damage of the current cycle. L/M shortcuts can also be used for one-touch access.

Select [status I/m] and press the [OK] Button key to proceed, the display is as follows:

📌ECU lnfo

ECU vehicle information function retrieves information about the breakdown number, calibration number and vehicle calibration verification number.

Select [ECU information] and press the [OK] Button key to proceed. The display is as follows:

📌Data Langsung

View real-time data allows viewing real-time vehicle PID data, all supported data are displayed and can be viewed by quickly sealing pages with left/right buttons or selecting custom data for comparison.

📌O2 sensor

Oxygen sensors are tested to identify problems related to fuel efficiency and vehicle emissions. The oxygen sensor test does not support the can communication protocol, which is available in 6 modes for vehicles with the can communication protocol.

📢 Nota:

1. please allow 1-3cm error due to manual measurement. Please make sure you don't mind before you bid.

2. due to the difference between different monitors, the picture may not reflect the actual color of the item. Thanks!